iglidur® B - Material data

Materials table

Genera l features	Unit	iglidur® B	test method
Density	g/cm³	1,15
Colour		Gray
Max. humidity absorption at 23°C/50% R. H.	% weight	1,0	DIN 53495
Max. water absorption	% weight	6,3
Coefficient of surface friction, dynamic, against steel	μ	0,18–0,28
pv value, max. (dry)	MPa x m/s	0,15
Mechanical properties
Bending E-module	MPa	1.800	DIN 53457
Tensile strength at +20 °C	MPa	55	DIN 53452
compressive strength	MPa	20
Maximum recommended surface pressure (20° C)	MPa	40
Shore D-hardness		69	DIN 53505
Physical and thermal properties
Max. long term application temperature	°C	+100
Max. short term application temperature	°C	+130
Minimum application temperature	°C	-40
thermal / heat conductivity	W/m x K	0,24	ASTM C 177
Coefficient of thermal expansion (at 23° C)	K^–1 x 10^–5	12	DIN 53752
Electrical properties
Specific forward resistance	Ωcm	> 10¹⁰	DIN IEC 93
surface resistance	Ω	> 10⁹	DIN 53482

'Table 01: Material Data

Figure 01: Permitted PV values for iglidur® B bearings with 1 mm wall thickness in dry operation against a steel shaft, at 20°C, installed in a steel housing.

X = Surface speed [m/s]
Y = Load [MPa]

The compressive strength of the iglidur® B bearings is on the one hand low, but on the other, is an important property of the bearing. They are mainly used where vibration dampening and acoustic separation are required.

Figure 02: Maximum recommended surface pressure dependent on the temperature (40 MPa to +20 °C)

X = Temperature [°C]
Y = Load [MPa]

Figure 03: Deformation under load and temperatures

X = Load [MPa]
Y = Deformation [m/s]

Mechanical properties

Maximum recommended surface pressure represents a mechanical material parameter. Tribological conclusions cannot be drawn from it. The pressure resistance of iglidur® B bearings declines with increasing temperatures. Fig. 02 clarifies this connection.

The deformation at 40 MPa at room temperature is 5.3% (Fig. 03).

Maximum surface speed

m/s	Rotary	oscillating	Linear
Constant	0,7	0,5	2
Short-term	1	0,7	3

Table 02: Maximum surface speeds

Permitted surface speeds

iglidur® B bearings can be continuously used in rotations for up to 0.7 m/s. The frictional heat provides the speed limits.

Because of the interactions, the specified maximum values are often not accomplished in practice.

Surface speed

p x v value and lubrication

iglidur® B	Operating temperature
Lower	- 40 °C
Upper, long-term	+ 100 °C
Upper, short-term	+ 130 °C
Secure axially in addition	+ 50 °C

Table 03: Temperature limits for iglidur® B

Temperatures

The operating temperature of the iglidur® B bearings is limited to 100° C. From 50° C onward, the very soft bearing should be mechanically fastened, so that the danger of bushings creeping out of the bores is avoided. The wear resistance too declines disproportionately from 70° C.

Temperatures, coefficient of thermal expansion

Figure 04: Coefficients of friction dependent on the surface speed, p = 0,75 MPa

X = Surface speed [m/s]
Y = Coefficient of friction μ

Figure 05: Coefficients of friction dependent on the load, v = 0,01 m/s

X = Load [MPa]
Y = Coefficient of friction μ

Friction and wear

The coefficients of friction increase slightly with the speed and decrease with the load. Shaft surface finishes between 0.4 and 0.6 Ra are ideal. Providing the bearing load is not too high, the attained coefficients of wear are very good. An increase in load results in a disproportionate increase in abrasion.

iglidur® B	Dry	Grease	Oil	Water
Coefficients of friction µ	0,18 - 0,28	0,09	0,04	0,04

Table 04: Coefficients of friction for iglidur® B against steel
(Ra = 1 µm, 50 HRC)

Coefficients of friction

Wear resistance

Figure 06: Wear, rotating application with different shaft materials, p = 1 MPa, v = 0.3 m/s

X = shaft materials
Y = wear [μm/km]

A = Aluminum, hard-anodized
B = machining steel
C = Cf53
D = Cf53, hard chrome-plated
E = St37
F = V2A
G = X90

Shaft materials

The influence of the shaft material is not very large in wear resistance.

Figures 06 and 07 clarify that very similar wear data are attained with different shaft materials. If high operational performances are expected, the bearing load should not be too high.

Shaft materials

Figure 07: Wear in pivoting and rotating applications with Cf53 dependent on the load

X = Load [MPa]
Y = Wear [μm/km]

A = Rotating
B = Pivoting

Medium	Resistance
Alcohols	+ to 0
Hydrocarbons	-
Fats, oils, without additives	-
Fuels	-
Diluted acids	0 to -
Strong acids	-
Diluted bases	-
Strong bases	-

+ resistant 0 partially resistant - non-resistant
All specifications at room temperature [+20°C] Table 05: Chemical resistance of iglidur® B

Electrical properties

Specific forward resistance	> 10¹⁰ Ωcm
Surface resistance	> 10⁹ Ω

Chemical resistance

iglidur® B bearings are not very resistant to chemicals For chemical resistance, there are other iglidur® materials available with better properties.

Radioactive rays

iglidur® B bearings are radiation resistant up to a radiation intensity of 3 x 10² Gy.

UV-resistant

iglidur® B bearings are not resistant to the influence of UV rays.

Vacuum

The use in vacuum is possible only conditionally. Only dry bearings made of iglidur® B should be tested in vacuum.

Electrical properties

Bearings made of iglidur® B are electrically insulating.

Maximum moisture absorption
by +23 °C/50 % r. F.	1,0 weight-%
Max. water absorption	6,3 weight-%

Table 06: Moisture absorption of iglidur® B

Effect of moisture absorption on plain bearings

Diagram 10: Effect of moisture absorption

X = Moisture absorption [weight %]
Y = Reduction of inside diameter [%]

humidity absorption / moisture absorption

The moisture absorption is relatively high and must be considered in the selection and design.

Diameter d1 [mm]	Shaft h9 [mm]	iglidur® B D11 [mm]	Housing H7 [mm]
Up to 3	0 - 0,025	+0,020 +0,080	0 +0,010
> 3 to 6	0 - 0,030	+0,030 +0,105	0 +0,012
> 6 to 10	0 - 0,036	+0,040 +0,130	0 +0,015
> 10 to 18	0 - 0,043	+0,050 +0,160	0 +0,018
> 18 to 30	0 - 0,052	+0,065 +0,195	0 +0,021
> 30 to 50	0 - 0,062	+0,080 +0,240	0 +0,025
> 50 to 80	0 - 0,074	+0,100 +0,290	0 +0,030

Table 07: Important tolerances for iglidur® B bearings according to ISO 3547-1 after the press-fit.

Installation tolerances

iglidur® B bearings are standard bearings for shafts with h-tolerance (recommended minimum h9).

The bearings are designed for press-fit in a housing with h7 tolerance. After the installation in a housing with nominal diameter, the inner diameter of the bearing automatically adjusts to the D11 tolerance. In certain dimensions the tolerance in dependence on the wall thickness deviates from this (See delivery program )

คุกกี้มีความสำคัญเพราะจะช่วยให้เว็บไซต์ปฏิบัติงานได้ถูกต้องเหมาะสมเพื่อให้เราสามารถเสนอประสบการณ์การใช้งานที่น่ารื่นรมย์ยิ่งขึ้น เราจึงต้องใช้คุกกี้เพื่อเก็บข้อมูลของท่าน ซึ่งจะช่วยให้เราสามารถเสนอการล็อกอินเข้าสู่ระบบที่ปลอดภัย สามารถรวบรวมข้อมูลทางสถิติเพื่อการใช้งานเว็บไซต์ที่ดียิ่งขึ้น รวมทั้งสามารถเสนอเนื้อหาที่ตรงกับความต้องการของท่านได้ กรุณาคลิกที่ "นโยบายการคุ้มครองข้อมูลส่วนบุคคล“เพื่อดูรายละเอียดเกี่ยวกับประเภทของคุกกี้ที่เราใช้และดูข้อมูลตัวเลือกต่างๆในกรณีที่ท่านต้องการถอนสิทธิ์.

การใช้บริการเว็บไซต์นี้จะถือว่าท่านยอมรับการใช้งานคุกกี้ของเรา นโยบายการคุ้มครองข้อมูลส่วนบุคคล. ใช่ ข้าพเจ้ายอมรับ

ประเทศ/ภูมิภาค

เมื่อเลือกประเทศของคุณ คุณจะเห็นข้อเสนอและข้อมูลในท้องถิ่น.

โปรดเลือกที่อยู่การจัดส่ง

iglidur® B - Material data

Materials table

Mechanical properties

Maximum surface speed

Permitted surface speeds

Temperatures

Friction and wear

Shaft materials

Electrical properties

Chemical resistance

Radioactive rays

UV-resistant

Vacuum

Electrical properties

humidity absorption / moisture absorption

Installation tolerances

ที่ปรึกษาและการสนับสนุน

เรายินดีให้คำปรึกษากับคุณ

จัดส่งและให้คำปรึกษา

โปรดเลือกที่อยู่การจัดส่ง

iglidur® B - Material data

Materials table

Mechanical properties

Maximum surface speed

Permitted surface speeds

Temperatures

Friction and wear

Shaft materials

Electrical properties

Chemical resistance

Radioactive rays

UV-resistant

Vacuum

Electrical properties

humidity absorption / moisture absorption

Installation tolerances

ที่ปรึกษาและการสนับสนุน

เรายินดีให้คำปรึกษากับคุณ

จัดส่งและให้คำปรึกษา

ประเทศ/ภูมิภาค

ตั้งค่าภาษา

Page not found

ตะกร้าสินค้า

ตะกร้าสินค้า